| Ferguson | TX100 59J7 | Field collapse | FOP chip TDA3652 – check for dry joints at scan coil plug under plastic cross member | |||
| Ferguson | TX100 (Turkish) | Switches to Stby after a while. | Change two 5V regulators in the control board.(TDD1605) | |||
| Ferguson | TX100 | WONT CHANGE CHANNELS WHEN COLD | C261 ( 1mfd ) | |||
| Ferguson | TX100 | Will only tune on channel 1 & 8. | IC905. | |||
| Ferguson | TX100 | Will not tune in. | IC1301 prescale chip. | |||
| Ferguson | TX100 | Will not tune in. | XL 1801 scope or meter on pin 24 clears fault. | |||
| Ferguson | TX100 | Will not store more then one channel | TR2016 , D2025 , IC2006 , change R2070 to 5k6. | |||
| Ferguson | TX100 | Will not store have to retune at each switch on | TR2017 ( BC307 ) u/s in read write modify circuit | |||
| Ferguson | TX100 | Width – reduced. | R709 o/c. | |||
| Ferguson | TX100 | Width – reduced. | Coil fitted on E/W PCB pluged into main PCB link it out. | |||
| Ferguson | TX100 | Width – reduced & ripply picture. | R143 ( 350uf ) high. |
| Ferguson | TX100 | Width – reduced – top foldover. | C115 ( 8200pf ) | |||
| Ferguson | TX100 | White raster. | C726 ( 22u f , 250v ) o/c , | |||
| Ferguson | TX100 | White raster with flyback lines. | C605 ( 4.7u f ) o/c. | |||
| Ferguson | TX100 | Volume will not go to min. | D5. | |||
| Ferguson | TX100 | Video faults. | C118 ( 8200pf ) leaky. | |||
| Ferguson | TX100 | Unlocked line over locked picture. | C754 ( 150nf ) | |||
| Ferguson | TX100 | Uncontrollable sound. | Crack in print PL22/3. | |||
| Ferguson | TX100 | Uncontrollable sound. | D2002 ( PH425 ) slight leak turning TR2006. | |||
| Ferguson | TX100 | Tuning varying. | Poor connection on prescaler on VHF tuner. | |||
| Ferguson | TX100 | Tuning jumps through higher band. | C365 should be a 25u f not 2.2u f. | |||
| Ferguson | TX100 | Tuning drifting in and out of tune. | Remake connections on plug to top of tuner. | |||
| Ferguson | TX100 | Tripping. | TR16 s/c. | |||
| Ferguson | TX100 | Tripping fast & relay chattering. | Line o/p transistor s/c , D26 leaky. | |||
| Ferguson | TX100 | Tripping – slight. | C118 ( 8200pf ) leaky. | |||
| Ferguson | TX100 | Tripping – no go. | Disconect pin 10 LOPTX if short across 119v rail – LOPTX |
| Ferguson | TX100 | Top frame foldover – width reduced. | C115 ( 8200pf ) | |||
| Ferguson | TX100 | Sync – hold break-up & bright blue picture. | TR10 ( T6071V ) | |||
| Ferguson | TX100 | Stuck in standby. | TR9 ( BC237B ) relay driver. | |||
| Ferguson | TX100 | Stuck in standby. | Drys on TR901 regulator. | |||
| Ferguson | TX100 | Stuck in st/by | BC237B tr9 relay driver | |||
| Ferguson | TX100 | StBy light works but goes off if channel changed | Check 12V drop across RL1 replace TR9 | |||
| Ferguson | TX100 | Static on screen after switching off. | Fit 10MR across neutral poles of on/off switch. | |||
| Ferguson | TX100 | Startup – intermittent. | Operates if on/off sw is pressed , R117 o/c , C139 o/c , TR9. | |||
| Ferguson | TX100 | Startup – intermittent. | Remote control unit. | |||
| Ferguson | TX100 | Startup – intermittent. | C139 o/c. | |||
| Ferguson | TX100 | Standby – ticking in standby only. | T1 chopper transformer. | |||
| Ferguson | TX100 | Standby – LED on – blank raster – 88 on disp | Replace R1831. | |||
| Ferguson | TX100 | Standby – intermittent standby – mute LED. | DJ on R132 ( 4.7R ) , dry on T1. | |||
| Ferguson | TX100 | Standby – at switch on. | TR9 ( BC237B ) | |||
| Ferguson | TX100 | Standby – at switch on or maximum sound. | CRT faulty. |
| Ferguson | TX100 | Standby – & channel change – intermittent. | Drys on TR901 regulator. | |||
| Ferguson | TX100 | St/by only | Dis’ing st/by plug gives pic but mute & st/by light on – SAA5012 | |||
| Ferguson | TX100 | Sound muted & no signal – intermittent. | C22 ( 330pf ) | |||
| Ferguson | TX100 | Sound muted & intermittent channel change. | On/off switch. | |||
| Ferguson | TX100 | Sound muted & colour low. | IC8 ( M7812CT ) | |||
| Ferguson | TX100 | Sound muted & channel change – intermittent. | On/off switch ( may have blown BU508 ) | |||
| Ferguson | TX100 | Sound intermittent. | Drys on R95 ( 2.2R ) | |||
| Ferguson | TX100 | Sound goes off after a few hours. | SPK o/c speech coil when warm. | |||
| Ferguson | TX100 | Sound at maximum or in standby at switch on. | CRT faulty. | |||
| Ferguson | TX100 | Sound – picture looks like tuner intermittent | DJ on CR1801 ( crystal ) on PC1544 panel. | |||
| Ferguson | TX100 | Snowy picture. | IC1 | |||
| Ferguson | TX100 | Smearing on one colour. | R601 ( 100k ) high. | |||
| Ferguson | TX100 | Shutdown – switching off after a few minutes. | Chopper transformer ( winding 50R ) should be 0.5R . | |||
| Ferguson | TX100 | Set switched on all right and channel one was disp | The PCD8571P memory chip IC 1805 was faulty. | |||
| Ferguson | TX100 | Remote volume , contrast , colour inoperative. | Fit a link LK11 on PC1564 if missing. |
| Ferguson | TX100 | Remote functions – intermittent. | Tube base arching. | |||
| Ferguson | TX100 | relay chatters only | check lopt, lop tr. If in psu check C119 22µ – 12v supply low at 10v | |||
| Ferguson | TX100 | Relay chattering. | TR10 fibre washer has pin hole in it. | |||
| Ferguson | TX100 | Relay chattering. | Check TR73 for o/c or DJ , C137 s/c , D26 s/c. | |||
| Ferguson | TX100 | Relay chattering. | D26 s/c , D28 s/c , check TR10 insulator for pin holes. | |||
| Ferguson | TX100 | RELAY CHATTERING OR DEAD | CHECK C112 , C113 , C119 AND S mode TX | |||
| Ferguson | TX100 | Relay chattering & fast tripping. | Line o/p transistor s/c , D26 leaky , D28 ( BY299 ) s/c. | |||
| Ferguson | TX100 | Random channel change | D/J on L20 | |||
| Ferguson | TX100 | Radom LED display & no picture. | R1831 on remote panel ( feed to 5C reg IC ) | |||
| Ferguson | TX100 | R106 burns up. | C110 220 385v leaky under load. | |||
| Ferguson | TX100 | Purity – poor. | Lower degauss coil connection. | |||
| Ferguson | TX100 | PULSATES ON HIGH BRIGHTNESS SCENES ESP WHEN COLD | C117 ( 100mfd , 16v ) | |||
| Ferguson | TX100 | Poor vertical sync – low contrast. | IC2 ( TDA3540 ) | |||
| Ferguson | TX100 | Poor teletext. | TR7 must be replaced with ZTX650 or ZSCZ655. | |||
| Ferguson | TX100 | Poor sync with frame roll on dark picture. | IC1033 ( SAA5030 ) |
| Ferguson | TX100 | POOR SOUND | C82 5.6pF | |||
| Ferguson | TX100 | Poor grey scale – then no video. | TR63 or one of the driver transistors faulty. | |||
| Ferguson | TX100 | Poor beam sensing. | D1 leaky. ` | |||
| Ferguson | TX100 | Picture ripply & lack of width until warm. | R143 ( 350uf ) high. | |||
| Ferguson | TX100 | Picture pulsating – colours changing. | C115 ( 8200pf ) | |||
| Ferguson | TX100 | Picture looks plastic & no colour. | C23 o/c , L2 o/c. | |||
| Ferguson | TX100 | Picture Dull – weak contrast. | TR2. | |||
| Ferguson | TX100 | Picture displaced to right – black band. | R48 ( 180k ) . | |||
| Ferguson | TX100 | Patterning on all channels. | C5 & C7 missing ( tuning volts decoupling ) | |||
| Ferguson | TX100 | Partial field collapse | Replace TDA3652 with 3654 & R96 to 3k3 | |||
| Ferguson | TX100 | No volume up – standby – mute. | IC902 ( ML923 ) . | |||
| Ferguson | TX100 | No video & poor grey scale – intermittent. | TR63 or one of the driver transistors faulty. | |||
| Ferguson | TX100 | No tuning. | C2022 ( 330pf ) | |||
| Ferguson | TX100 | No text – Intermittent colour – frame jitter. | IC1033 ( SAA5030 ) | |||
| Ferguson | TX100 | No sync. | C66 ( 2200pf ) changing value. |
| Ferguson | TX100 | No sync, sound or Txt | Link 2 fitted to isolate sync to txt panel and now ok – left in this state rather than repair fault on Txt panel | |||
| Ferguson | TX100 | No sync | C63 150pf s/c | |||
| Ferguson | TX100 | No standby – mute – volume +. | IC902 ( ML923 ) . | |||
| Ferguson | TX100 | No sound/pic – HT OK | TDA2578A (line osc not working) | |||
| Ferguson | TX100 | No sound. | R21 o/c , R95 ( 2.2R ) o/c by sound IC. | |||
| Ferguson | TX100 | No sound. | Line sync processor IC. | |||
| Ferguson | TX100 | No sound. | IC4 ( pin 13 grounded internally within IC ) | |||
| Ferguson | TX100 | No sound or picture – all LEDs on. | R1931 ( 47R ) on remote board. | |||
| Ferguson | TX100 | No sound or picture – 12v rail low. | D15 s/c ( 119v rectifier ) R116 gets very hot. | |||
| Ferguson | TX100 | no sound or pic – just purring, until heated | C117 100µ 16v chopper coupler leaky | |||
| Ferguson | TX100 | No sound & no field sync. | D33 leaky. | |||
| Ferguson | TX100 | No sound & frame collapse – no brit control. | IC8. | |||
| Ferguson | TX100 | No sound – blank raster. | C24 ( 10nf ) leaky. | |||
| Ferguson | TX100 | No signal & sound mute – intermittent. | C22 ( 330pf ) | |||
| Ferguson | TX100 | No remote operation. | IC1803 ( u PC7805 ) |
| Ferguson | TX100 | No remote operation – blank raster. | IC1807 ( SAB3035 ) | |||
| Ferguson | TX100 | No remote if close. | Poor earth connection on screening. | |||
| Ferguson | TX100 | No remote functions. | Over-ride contacts of on/off switch s/c. | |||
| Ferguson | TX100 | No remote control or front control operation. | Change IC902 ( SAA3004P ) on infra red pre amp board. | |||
| Ferguson | TX100 | No red. | R609 ( 100k ) o/c. | |||
| Ferguson | TX100 | no r/c or chan down on tv front panel | st/by contacts on mains sw perm shorted | |||
| Ferguson | TX100 | No picture. | IC3 RGB volts clamped low & cathodes – CRT faulty. | |||
| Ferguson | TX100 | No picture or sound – all LEDs on. | R1931 ( 47R ) on remote board. | |||
| Ferguson | TX100 | No picture or sound – 12v rail low. | D15 s/c ( 119v rectifier ) R116 gets very hot. | |||
| Ferguson | TX100 | No picture – random LED display. | R1831 on remote panel ( resistor feed to 5C reg IC ) | |||
| Ferguson | TX100 | No picture – no 12v rail. | 120v & 20v rail ok , R73 ( 9k1 ) o/c. | |||
| Ferguson | TX100 | No picture – low 12v rail. | IC1807 ( SAB3035 ) | |||
| Ferguson | TX100 | No picture – line transistor overheating. | D26 s/c , TR73 o/c , R711 o/c. | |||
| Ferguson | TX100 | No output from IC1807. | XL1801 crystal not oscillating. | |||
| Ferguson | TX100 | No mute – standby – volume +. | IC902 ( ML923 ) . |
| Ferguson | TX100 | No line or frame sync. | C63 ( 150pf ) across IC4 ( TDA2578A ) | |||
| Ferguson | TX100 | No green. | R609 ( 100k ) o/c. | |||
| Ferguson | TX100 | No go – relay chatters. | Line transistor s/c. | |||
| Ferguson | TX100 | No go – low/no 119V rail. | C121 ( 47uf , 160V ) | |||
| Ferguson | TX100 | No front control or remote operation. | Change IC902 ( SAA3004P ) on infra red pre amp board. | |||
| Ferguson | TX100 | No frame sync – no sound. | D33 leaky. | |||
| Ferguson | TX100 | No frame sync – line hold ok. | C64 ( 100nf ) s/c. | |||
| Ferguson | TX100 | No colour – picture looks plastic. | C23 o/c , L2 o/c. | |||
| Ferguson | TX100 | No colour | pin 5 col dec chip reads low & doesn’t vary with sat, C47 2µ2 25v non pol cap faulty | |||
| Ferguson | TX100 | No channel change – intermittent. | IC2007 ( M293B1 ) | |||
| Ferguson | TX100 | NO CHAN DISP OR TUNING | TR7 ZTX650 ( NO 9v TO REM PANEL ) | |||
| Ferguson | TX100 | No britness control or sound & frame collapse | IC8. | |||
| Ferguson | TX100 | No blue. | R609 ( 100k ) o/c. | |||
| Ferguson | TX100 | No AV on channels 8 & 9 , 1-7 ok. | Cut link A on pin 8 of IC1806 on remote panel. | |||
| Ferguson | TX100 | Mute LED on. | D116 s/c. |
| Ferguson | TX100 | Mute LED on – sticking on channel 8. | DJ on R132 ( 4.7R ) | |||
| Ferguson | TX100 | Low contrast int | Check plug to CRT heaters | |||
| Ferguson | TX100 | LOP transistor short lived – pic twitches | Line hold pot | |||
| Ferguson | TX100 | Lines on picture ( black ) & frame jitter. | C97 ( 100nf ) o/c. | |||
| Ferguson | TX100 | Line tear from switch on for few mins. | C141 ( 10uf ) | |||
| Ferguson | TX100 | Line speed error on parts of screen. | TR8. | |||
| Ferguson | TX100 | Line o/p trs last only a short time | Check for dry joints at scan coil plug | |||
| Ferguson | TX100 | Line – twitch. | Change C75 to 22u f , TR10. | |||
| Ferguson | TX100 | LEDs all on – no sound or picture. | R1931 ( 47R ) on remote board. | |||
| Ferguson | TX100 | Lack of width (110 deg) | 90 deg parts fitted in error | |||
| Ferguson | TX100 | Lack of width | LOPTx faulty | |||
| Ferguson | TX100 | Intermittent. | DJ on T1 pins 5&6. | |||
| Ferguson | TX100 | INTERMITTENT SWITCH OFF | IC241 M494 ON REMOTE PANEL | |||
| Ferguson | TX100 | Intermittent corruption of the front panel display | Tube base arcing internally | |||
| Ferguson | TX100 | Int start up aft briefly sw off | Dry joints T1 |
| Ferguson | TX100 | Int sound | R95 2R2 dry joints | |||
| Ferguson | TX100 | Int R/C | Ceramic reonator CR241 (500Hz) | |||
| Ferguson | TX100 | Int chan change & int goes into st/by | Low volts (2V) at pin 20 IC901 of R/C proc (9v) reg tr901 dry joints | |||
| Ferguson | TX100 | Green picture. | R601 ( 110k ) high. | |||
| Ferguson | TX100 | GOES OFF AFTER A FEW MINS. | CHOPPER TRANSFORMER | |||
| Ferguson | TX100 | Goes into chan search when afc removed | D2026-2029 1N4148 leaky | |||
| Ferguson | TX100 | Frame jitter – intermittent colour – no text. | IC1033 ( SAA5030 ) | |||
| Ferguson | TX100 | Frame jitter – black lines on picture. | Check C95 , C97 ( 100nf ) , C98 for o/c or leaky. | |||
| Ferguson | TX100 | Frame collapse. | D4 o/c , or IC6 faulty can burn up R97. | |||
| Ferguson | TX100 | Frame collapse. | C72 ( 470nf ) leaky. | |||
| Ferguson | TX100 | Frame collapse – after 10 mins. | Scan assy s/c solder on rear connection to PL14. | |||
| Ferguson | TX100 | Frame – scan distorted. | IC TDA3651 frame IC. | |||
| Ferguson | TX100 | Frame – roll – poor sync on dark picture. | IC1033 ( SAA5030 ) | |||
| Ferguson | TX100 | Frame – IC blowing. | Check C95 , 97 , 98 for o/c or leaky. | |||
| Ferguson | TX100 | Frame – hold critical – wrong end of pot. | R788 should be 180k not 220k. |
| Ferguson | TX100 | Frame – foldover. | D4 s/c. | |||
| Ferguson | TX100 | Frame – foldover. | R98 o/c. | |||
| Ferguson | TX100 | Frame – foldover – top half of scan. | C99 ( 100uf ) s/c. | |||
| Ferguson | TX100 | Frame – excessive height – poor linearity. | D137 ( 68V ) zener ( it will check out ok ) | |||
| Ferguson | TX100 | Frame – collapse – resistor R103 overheats. | C95 ( 10nf ) s/c. | |||
| Ferguson | TX100 | Frame – collapse – no sound – no brit control | IC8. | |||
| Ferguson | TX100 | Flyback – lines at top 1″ of picture. | C99. | |||
| Ferguson | TX100 | Flyback – lines & bright raster. | TR60 on CRT base. | |||
| Ferguson | TX100 | Flyback – lines – peak whites. | C605 ( 4.7u f ) o/c. | |||
| Ferguson | TX100 | Flashing for first 1/2 hour. | DJ on LOP TX earth. | |||
| Ferguson | TX100 | Field lin | TDA3651 | |||
| Ferguson | TX100 | Field collapse | MC7812CT 12v reg IC8 | |||
| Ferguson | TX100 | Fast tripping. | LOPTX | |||
| Ferguson | TX100 | East west – fault. | TR73 faulty or DJ , R711 ( 2.70 ohm ) , D28 s/c or leaky , D26. | |||
| Ferguson | TX100 | East west – fault & incorrect brightness. | D28 s/c or leaky. |
| Ferguson | TX100 | Display – random LED display – no picture. | R1831 on remote panel ( resistor feed to 5C reg IC ) | |||
| Ferguson | TX100 | Display – no LED display – HT & EHT ok. | IC1805. | |||
| Ferguson | TX100 | Display – faulty. | D4 on stereo bar grap display brd revrse leaky. | |||
| Ferguson | TX100 | Dead. | Print around on/off switch burnt up. | |||
| Ferguson | TX100 | Dead. | IC TDA4600. | |||
| Ferguson | TX100 | Dead. | C121 o/c. | |||
| Ferguson | TX100 | Dead. | D15 iBY299 ) in psu s/c. | |||
| Ferguson | TX100 | Dead. | D12 o/c. | |||
| Ferguson | TX100 | Dead. | C112 o/c. | |||
| Ferguson | TX100 | Dead. | D20 s/c. | |||
| Ferguson | TX100 | Dead. | Approx 119v on D19 T3 or cracks in print around P2 & 10. | |||
| Ferguson | TX100 | Dead. | R108 o/c. | |||
| Ferguson | TX100 | Dead. | Relay u/s , C115 s/c ( 8n2 ) R113 overheating. | |||
| Ferguson | TX100 | Dead. | R115 ( 270k ) high ( 1.2R ) , check print bt IC9 & R143 , TR8 o/c | |||
| Ferguson | TX100 | Dead. | BC372 s/c plus feed R143 o/c , D28 ( BY299 ) s/c. |
| Ferguson | TX100 | Dead with ticking chopper tfmr | C121 47µ 160v low | |||
| Ferguson | TX100 | Dead with squeal from LOPTx | LOPTx faulty | |||
| Ferguson | TX100 | Dead with machine gun type tripping | LOPTx s/c winding | |||
| Ferguson | TX100 | Dead with faint hum from spkr | HT ok on dummy load – low when connected normally – LOPTx | |||
| Ferguson | TX100 | Dead with chopper TX ( T1 ) ticking. | C121 ( 47uF/160V ) low value. | |||
| Ferguson | TX100 | Dead with 120v on LOPTr | No line dr – Tr8 BC372, R143 6R8 hi res & LOPTx | |||
| Ferguson | TX100 | Dead 2.5A fuse blown | Green faces when fuse replaced – degaussing therm faulty | |||
| Ferguson | TX100 | Dead – static on screen customer said. | Fit 10MR across neutral poles of on/off switch. | |||
| Ferguson | TX100 | Dead – relay RL1 chattering. | TR73 o/c , drys on C137 s/c , D26 s/clTR10 s/c or washer. | |||
| Ferguson | TX100 | Dead – relay chattering. | TR10 fibre washer has pin hole in it. | |||
| Ferguson | TX100 | Dead – R143 burnt up – from cold. | TR8 s/c. | |||
| Ferguson | TX100 | Dead – R116 burnt up. | SCR1 s/c , R116. | |||
| Ferguson | TX100 | Dead – no volts on pin 9 of IC7. | R117/R118 o/c. | |||
| Ferguson | TX100 | Dead – no line drive. | C66 o/c. | |||
| Ferguson | TX100 | Dead – no line drive. | IC9 15v reg. |
| Ferguson | TX100 | Dead – no 200v rail. | T2 DJ on secondary. | |||
| Ferguson | TX100 | Dead – no 12v rail – 120v & 20v rail ok. | 120v & 20v rail ok , R73 ( 9k1 ) o/c. | |||
| Ferguson | TX100 | Dead – low HT at 50v | C121 22µ ht decoupler leaky | |||
| Ferguson | TX100 | Dead – keeps blowing fuse. | TR6 s/c , TR10 s/c. | |||
| Ferguson | TX100 | Dead – intermittent. | Drys on mains supply to PCB , TR8 ( BC372 ) o/c line driver | |||
| Ferguson | TX100 | Dead – int to start with | Dry joints chopper tfmr sec chassis con | |||
| Ferguson | TX100 | Dead – from cold – ok after 20 seconds. | TR8 s/c can burn up R143. | |||
| Ferguson | TX100 | Dead – for 10 mins. | C121 o/c. | |||
| Ferguson | TX100 | Dead – diodes s/c. | BU508 & surge lim resistor. | |||
| Ferguson | TX100 | Dead – D25 , IC6 , C99 going s/c. | R98 , R133 o/c , caused by C136 ( 2200uf ) breaking down. | |||
| Ferguson | TX100 | Dead – BU508 s/c – then width reduced. | LOPTX | |||
| Ferguson | TX100 | Dead – blowing TR10. | DJ/broken print around IC1804. | |||
| Ferguson | TX100 | Dead – blowing TR10 at switch on. | Lead of C140 12pf under board arcing on 15v rail. | |||
| Ferguson | TX100 | Dead – blowing T2.5A violently. | C107 s/c. | |||
| Ferguson | TX100 | Dead – blowing LOP transistor. | Also change TR8 ( BC372 ) |
| Ferguson | TX100 | Dead – blowing LOP transistor BU508. | On/off switch. | |||
| Ferguson | TX100 | Dead – blowing LOP transistor at switch on. | RV91 o/c ( line hold control ) , D15 ( BY299 ) s/c. | |||
| Ferguson | TX100 | Dead – blowing fuse FS1 – violently. | C107 ( 470pf ) | |||
| Ferguson | TX100 | Dead – blowing chopper TR6 at switch onn | D10 ( 6.8v zener ) s/c , D15 ( BY299 ) s/c. | |||
| Ferguson | TX100 | Dead – 205v rail down to around 35v. | C726 ( 22u f , 250v ) o/c , | |||
| Ferguson | TX100 | Dead – 12v rail low – no sound or picture. | D15 s/c ( 119v rectifier ) R116 gets very hot. | |||
| Ferguson | TX100 | Dead – 119v or 20v lines low. | D20 s/c. | |||
| Ferguson | TX100 | Dead – 1.6A fuse o/c | Chopper tr BU508A s/c; R121 27R o/c;TDA4600 u/s; R115 270k – when powered confetti type spots on screen when tapped – C120 1n8 square blue cap dry jointed – caused demise of all other parts. | |||
| Ferguson | TX100 | Dead | No HT from chopper cct – D15 BY299 HT rect s/c | |||
| Ferguson | TX100 | Dead | s/c between pins 10-8-7-6 of LOPTx – faulty | |||
| Ferguson | TX100 | Dead | No HT even on dummy load – C117 100µ | |||
| Ferguson | TX100 | Dead | BU508A LOP tr & BC372 line driver tr u/s | |||
| Ferguson | TX100 | Dead | D15 BY299 in psu s/c | |||
| Ferguson | TX100 | Dead | Check D28 ( BY299 ) if east west fault after replacment Check R711 ( 2K7 ) | |||
| Ferguson | TX100 | Dead | D15 BY299 SC |
| Ferguson | TX100 | Contrast control not operating. | DJ on R2010 on remote Rx board. | |||
| Ferguson | TX100 | Contrast – weak – poor vertical sync. | IC2 ( TDA3540 ) | |||
| Ferguson | TX100 | Contrast – weak – dull picture. | TR2. | |||
| Ferguson | TX100 | Colours changing – picture pulsating. | C115 ( 8200pf ) | |||
| Ferguson | TX100 | Colour – will not turn down. | R30 ( 15k ) o/c. | |||
| Ferguson | TX100 | Colour – low & sound muted. | IC8 ( M7812CT ) | |||
| Ferguson | TX100 | Channels – Sticking on ch 8 – mute LED on. | DJ on R132 ( 4.7R ) | |||
| Ferguson | TX100 | Channels – no channel change – remote ok. | TR901 o/c. | |||
| Ferguson | TX100 | Channels – all store the same. | TR2016 , 2017 , D2025 , R2070 , SAA5012 , M293 due to CRT flash. | |||
| Ferguson | TX100 | Channel change – & into standby intermittent. | Drys on TR901 regulator. | |||
| Ferguson | TX100 | Channel 11 displayed when on channel 1. | D4 on stereo bar graph display brd revrse leaky. | |||
| Ferguson | TX100 | Channel – 1&2 – 3&4 – 5&6 ect tune together. | IC342 ( pin 14 high all the time ) | |||
| Ferguson | TX100 | Chan display lit but no EHT | D2 on E/W vertical plug in pcb s/c | |||
| Ferguson | TX100 | Cast on colour. | C50 , C51 , C52 | |||
| Ferguson | TX100 | Buzz on sound in mute & at low volume | Replace TDA1701. |
| Ferguson | TX100 | Buzz on sound | CF1off | |||
| Ferguson | TX100 | BU508A overheats, int line hold. | R143 6R8 value gone high to about 100R | |||
| Ferguson | TX100 | Brightness – varies with flyback lines. | TR60 on CRT base. | |||
| Ferguson | TX100 | Brightness – level flicker on dark areas. | IC3 ( TDA3562A ) | |||
| Ferguson | TX100 | Brightness – incorrect & east west fault. | D28 s/c or leaky. | |||
| Ferguson | TX100 | Bright yellow/red pic at sw on | Settles down when heated – CRT low emission | |||
| Ferguson | TX100 | BRIGHT SCREEN , FLYBACK LINES | TR60 BC308 BCL. | |||
| Ferguson | TX100 | Bright red raster. | R604 , R608 , R612. | |||
| Ferguson | TX100 | Bright raster & flyback lines. | TR60 on CRT base. | |||
| Ferguson | TX100 | Bright green raster. | R604 , R608 , R612. | |||
| Ferguson | TX100 | Bright blue raster. | R604 , R608 , Rv12. | |||
| Ferguson | TX100 | Bright blue picture & line break-up. | TR10 ( T6071V ) | |||
| Ferguson | TX100 | Blue raster. | R605 o/c ( blue cathode volts about 70v ) | |||
| Ferguson | TX100 | Blue bright picture. | IC4 ( TDA2578A ) | |||
| Ferguson | TX100 | Blue band at top of picture. | C45 ( 470nf ) . |
| Ferguson | TX100 | Blows chopper Tr int | C118 ( 8.2nF ) replace with ( 6.8nF ) | |||
| Ferguson | TX100 | Blowing frame IC. | Change R96 to a 2.2k not 3.3 as mod sheet says. | |||
| Ferguson | TX100 | Blank raster. | R61 o/c , IC3 ( TDA3562A ) | |||
| Ferguson | TX100 | Blank raster – standby LED on – 88 on display | Replace R1831. | |||
| Ferguson | TX100 | Blank raster – no sound. | C24 ( 10nf ) leaky connected to pin 14 of IC2. | |||
| Ferguson | TX100 | Blank raster – no remote operation. | IC1807 ( SAB3035 ) | |||
| Ferguson | TX100 | Black band down left hand side. | R48 ( 180k ) . | |||
| Ferguson | TX100 | 88 on display – standby LED on – blank raster | Replace R1831. | |||
| Ferguson | TX100 | 12v rail low. | IC1807 ( SAB3035 ) | |||
| Ferguson | TX100 | 119v rail low – top foldover & width reduced. | C115 ( 8200pf ) | |||
| Ferguson | TX100 | Width excess with E-W bowing | L1 on E-W sub pcb (if fitted) shorted turns – from PL95 & PL96 on main board |
