This searches the Website not the forum

Thorn ICC7 Stock Faults

< Back

ICC7 GOES OFF AFTER 30SECS REPLACE CP29.
ICC7 AUTO VOL REDUCES WITH OSD , MEMBRANE FAULT.
ICC7 BALLOONING CL24, CL28 330N, CL21 6N1
ICC7 BLANK RASTER OSG OK, RI15(10R) .
ICC7 BLANK RASTER/NO SND TX07(BC846B) UNDER PCB.
ICC7 BLOWS 0R68 IN PSU, DL09 BA159 ON SECONDARY OF LOPTX.
ICC7 BRIGHT RASTER ,TT33 BC558 ON CRT PCB CAUSE CW01(680NF).
ICC7 BUH515/S2000AF3 CHOPTR TP29, CHANGE CP29 FROM 2.2NF TO 3.3NF.
ICC7 CHOPTR(BUH713)
ICC7 CLICKING SND ON NICAM – OK ON MONO 16.384KHZ XTAL ON NICAM PCB
ICC7 COLD IF INSTABILITY ,C525 1UF
ICC7 COLD STOPS,CP29,
ICC7 COLOR CAST 39K CRT BASE
ICC7 CONTROL RIBBON GREEN SIDE UP.
ICC7 DEAD 10 SECS OF RED LED TL17 ,DF16(BA157) ,DL18(1N4148).
ICC7 DEAD BSR51 LINE DRIVER TRANSISTOR TL17.
ICC7 DEAD DP17(BA157) DP28 BA159.
ICC7 DEAD DP54 DP55 RP62(0.1R) DF16(BA157) DL18 TL18 TP29 TP17.
ICC7 DEAD EHT RUSTLE, PCB REPAIR ,CP59 LEAKS(3300UF35V).
ICC7 DEAD EHT SURGE CP59 3300UF35V TDA8178FS
ICC7 DEAD EHT SURGE,RP39(120K)GLUE UNDER PCB
ICC7 DEAD FP01,RP01,RP02,TP20(BC548C),TL17(BSR51).
ICC7 DEAD FUSE DP50(BY399)+BUH515.
ICC7 DEAD FUSE FP01 CHOPTR TP29 IP01 TEA2261 + RP62 0R1
ICC7 DEAD FUSE+BUH515/S2000AF3+TEA2261+CP29(3N3F)
ICC7 DEAD FUSE+TP29+IP01+RP62(0R1).
ICC7 DEAD HT OK 3300UF 35V BEHIND LOPTX
ICC7 DEAD INT TP20(BC548C).
ICC7 DEAD IP01 TEA2261
ICC7 DEAD LED LIT 10 SECS TA8659, TL17 ,DF16, DL18 DP28 (BA157)
ICC7 DEAD LED LIT IF01(TDA8178F)
ICC7 DEAD LED ON,RP62 (0.1R), TDA8178F.
ICC7 DEAD LED RED FOR 10 SECONDS THEN OFF,TL17, DF16(BA157), DL18(1N4148)
ICC7 DEAD LED SHINES RED. RP62(0.1R) ,TDA8178F FIELD IC IF01.
ICC7 DEAD LED SURGE DF16(BA157) DL18+TL17.
ICC7 DEAD LOPTR S2000AF CAUSE CL21(11NF1K6V) LOOKS OK
ICC7 DEAD LOPTR(2SD1546 NO D OR R) +CL21(11N5F16KV) CL22(20NF400V)+TDA4950.
ICC7 DEAD LOPTR(2SD1546 NOT S2000A)
ICC7 DEAD LOPTR(2SD1546)+CL21(11N5F1K6V) CAUSE CRT ARCING INSIDE
ICC7 DEAD LOPTR(S2000AF)+RV01(5K6R),ADD 560R INTO DV01.
ICC7 DEAD MAINS SW IR01 MICRO
ICC7 DEAD NO LED ,TRIPPING, DP17(BA157).
ICC7 DEAD NO LINE DRIVE ,TL17(BSR51)+RP62(0R1)
ICC7 DEAD NO POWER GOOD 300V, TEA2261.
ICC7 DEAD PSU TICKS RP62 0R1 IF01 TDA8178F
ICC7 DEAD RED LED DL18 1N4148
ICC7 DEAD RP62 FIELD CHIP
ICC7 DEAD RP62 0R1 BA157 DL09, CL09. RP62
ICC7 DEAD SURGE TDA8178F DL09 BA157(PIN 12 LOPTX)
ICC7 DEAD TEA2261+DP28(BA159) 333LINKS
ICC7 DEAD TICKING RP62(0R1) IP01.
ICC7 DEAD TP29, TL19, DP50, CP22, DP17 , DP28
ICC7 DEAD, CHOPTR(BUH515)+IP01 TEA 2261,+RP62 0R1
ICC7 DEAD, NO LINE OSC . IRO1 MICRO (ST 6391B1/BC)PTNO IOO35850
ICC7 DEAD, RP62 0.1R . TDA8178F, FIELD IC
ICC7 DEAD/STBY RR83(150R)+RR18(27R).
ICC7 DISTORTED SND C131 10UF16V IN IF CAN
ICC7 EHT SURGE,ADD LINK TWEEN RP53 TEST POINT BP50, CAUSE CP59 3300UF35V
ICC7 EW COIL 1R+6.5R
ICC7 EW RASTER BENT SIDES TDA4950
ICC7 EXCESS BRILL RT05(10R) ON CRT BASE PANEL.
ICC7 FIELD BOTTOM FOLDOVER CF84 1UF (NR SCAN PLUG).
ICC7 FIELD CHIP ADD 3K9 PIN2/7+2V7ZD PIN7/CHASSIS .
ICC7 FIELD CHIP PHEONIX MOD KIT F8 CHANGE 2V0ZD TO 2V7ZD PIN7/CHASSIS .
ICC7 FIELD COLLAPSE ,RV72(22)RL11(15R)RF07(1M5)DF16(BA1257)DL11 (BA157) .
ICC7 FIELD COLLAPSE BA157 RV72(22R) RL11(15R).
ICC7 FIELD COLLAPSE RL11(15R) DL11(BA157) ,TDA8178F
ICC7 FIELD COLLAPSE RV72 (22R)RL11(15R)RF07(1M5)DF16(BA1257)DL11 (BA157).
ICC7 FIELD FOLDOVER RF23 RF07(1M5) RF21(0R68) DL09(BA157) DF17.
ICC7 FIELD FOLDOVER AT BOTTOM CF84 1UF(NR SCAN COILS PLUG)
ICC7 FIELD FOLDOVER TDA8178F LINK J238 .
ICC7 FIELD IC STV9379F, 3K9 ,2V1 ZENER
ICC7 FIELD LO HEIGHT RF23,PIN 12 LOPT RF07(1M5)RF21(0R68)DL09(BA157)DF17.
ICC7 FIELD MOD IF01(STV9379FS)ADD 3K9 PIN2/7 ADD BZX75C2V1 PIN7>]EARTH.
ICC7 FIELD TDA8178/STV9379F(ADD 3K9 TWEEN PINS 2/7,2V1 ZENER TWEEN PIN7 CHASS.
ICC7 INT DEAD HI HT 120VN .
ICC7 INT DEAD RESOLDER EVERYWHERE.
ICC7 INT LINES CS25(1UF) IN IF MODULE
ICC7 INT LOSS OF SIGNALS, IF JOINTS CS32/LA7550.
ICC7 INT LUM/CROMA WITH DOTS/LINES COIL IN IF MODULE.
ICC7 INT SIGNAL,DRY-JOINTS IN IF UNIT, AT CS32 WHICH IS ASSOCIATED WITH THE LA7550 CHIP IS10
ICC7 INT SND, RESOLDER TDA6200 CHIP IS04 ON THE NICAM BOARD.
ICC7 INT SND/PIC IF UNIT PINS
ICC7 INT STBY TR16 TR17. PIN 40 IV01, 9V=ON 0V=STBY TRIP
ICC7 INT TRIP, CRT FLASHOVER, NO RED RT08.
ICC7 LIKE CRT RT24/44/64 39K OR TEA5101A.
ICC7 LINE DRIVER TL17 DF16 IN FIELD CCT
ICC7 LINES ON PIC, IF MODULE CAPS C123 4.7UF,
ICC7 LO SND C514(1UF63V) IN IF CAN.
ICC7 LO WIDTH IG01 IG01 & CL24 440N.F
ICC7 LOPTRANSISTOR BLOWN CAUSE LINE DRIVER TX PINS.
ICC7 LOPTX (OREGA 40308-11 HR6354).
ICC7 LOPTX HR7317/HR6354 ICC8.
ICC7 LOPTX PULSING 40308-11=HR6354.
ICC7 LOW RED 39K ON CRT BASE.
ICC7 LOW SND C514 1UF 63V IN IF CAN.
ICC7 MICROPRO INT CONTROL ACTIONS.
ICC7 NEG PIC/SYNC C525 IN IF CAN
ICC7 NICAM CLICKS/MONO OK 16.384KHZ XTAL ON NICAM PCB
ICC7 NO BLUE RT66(1K).
ICC7 NO COLOR RC09 (22R) IV01 (TA8659) IE50 (TEA2114)
ICC7 NO EW CORRECTION, RG87(2R2),TG84
ICC7 NO FIELD, RL11(15R), DL11 (BA157),TDA8178F
ICC7 NO NICAM SND R501(33R) ON NICAM PCB
ICC7 NO NS CORRECTION TG38 TG84 BD137 RG87 (2R2) TG84
ICC7 NO PICTURE EHT OK, RD21(10R) ON CDI2000.
ICC7 NO PICTURE SNOWY OSD OK, RH01(22R).
ICC7 NO R/C OPERATION BA01.
ICC7 NO RED CRT FLASHOVER RT08(1K).
ICC7 NO SOUND HEADPHONE SOCKET.
ICC7 NO SOUND PIC PATTERN RESOLDER IF UNIT
ICC7 NO SOUND RS02(47R),RS03(33R),RS01(33R),RS04(27R).
ICC7 NO START. TL17 DF16 (BA157)
ICC7 NO SYNC CV54 0U1F
ICC7 NO SYNC CV54(0U1F)
ICC7 NO TEXT OSD OK, RV10(0R22),RV11(2R7).
ICC7 NO TEXT SAA5243
ICC7 NOT TUNING . RH04 27K (BEHIND LOPT)
ICC7 NO/INT SND RESOLDER ALL NICAM AREA.
ICC7 OSD INT/CONTROLS MEMBRANE .
ICC7 OSD=P1/NO REMOTE RESET HOLDCHANUP/CHANDWN AND POWER ON
ICC7 PATTERNING RESOLDER IF MODULE
ICC7 PIC NEGATIVE/SYNC C525 IN IF CAN
ICC7 PIC SIZE ON BRIGHTNESS(BALLONING) CL24, CL28 330N, CL21 6N1
ICC7 POOR FIELD LIN RF23(1R5) DL09(BA157) IF01.
ICC7 POOR FOCUS LOPTX
ICC7 POOR FOCUS , LEAD TO CRT FOCUS PIN
ICC7 POOR PIC WITH STREAKS R704 1.5K ON CRT BASE
ICC7 POOR PIC/COLOR RT24/44/64 39K TEA5101A
ICC7 POWER PULSES TV01 (BC558) DP17(BA157) NR CHOP/HSINK.
ICC7 POWER SHUTS DOWN TDA8178F SEE MOD
ICC7 POWER SHUTS DOWN,DL09 BA157 NR LOPTX.
ICC7 PSU REPAIR KIT PART NO 10268040
ICC7 PULSING 1 SEC TV01(BC558) LOPTX.
ICC7 RANDOM OSD FRONT PANEL MEMBRANE KEYPAD
ICC7 RED/GREEN LED, EHT SURGE,TP53 BC557
ICC7 RG85 ON NS PCB TG76 BD137
ICC7 RP62 IF01 TDA8178F
ICC7 S2000AF LOPTR,MOD RV01(4K7 TO 5K6), ADD 560R, RV03 SERIES ANODE DV01.
ICC7 SABA SB9221
ICC7 SHORT SQUEAL, NO 24V RP62 0R1+TDA8187 FIELD OUTPUT IF01.
ICC7 SMEARY PIC RT24/44/64(39K),TEA5101A
ICC7 SND LOW/DIST C514 1UF 63V IN IF CAN
ICC7 START/DEAD TP69(BC547C).
ICC7 STARTS/DEAD HT SETTING , POT SETTING.
ICC7 STBY DEAD. DP54 DP55 RP62(0R1) DF16 (BA157) DL18 TL18 TP29 TP17
ICC7 STBY LED FLASHES DP17 BA157 PSU
ICC7 SURGE ONLY, BURNT PCB FROM PIN3 LOPTX WHERE TRACK THIN
ICC7 SURGE ONLY,BA157 RECTIFIER DIODE DL09 FROM PIN 12 OF LOPTX
ICC7 TL17 LINE DRIVER DF16 BA157
ICC7 TOP CRAMP DL09,TDA8178F.
ICC7 TOPTEL 053 055
ICC7 TRIP TP66 BC858B/BC857C, EVEN IF IT TESTS OK. RECONNECT PIN 19 OF IV01.
ICC7 TRIPPING IA05.
ICC7 TRIPPING PSU IA05,DP26 TU01 BC558,TL17 DF16
ICC7 TRIPS 2 SECS DP24,DP26,DP27.
ICC7 TRIPS 4 TIMES DEAD DP17 BA157 BY PSU HEATSINK
ICC7 TRIPS DP17 IA05, DP26,DP24,DP27 TU01(BC558), TL17 ,DF16.
ICC7 TUNING DRIFT,TUNER+ TH01, TH02, TH03, TH04 TH05
ICC7 VENESION BLINDS C123 4U7F IN IF CAN.
ICC7 WARM DARK/NO PIC SND OK,LOPTX HTR PINS
ICC7 WEAK SND CS14(1UF63V) IN IF MODULE.

0 0 votes
Article Rating
Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

0 Comments
Inline Feedbacks
View all comments
Table of Contents
0
Would love your thoughts, please comment.x
()
x